english prs44_e.htm; updated: 01 FEB 2012; 19% VAT german

wave
2.4 GHz transmit modules and receiver series

The wave series of transmitter modules and receivers is our response to the confusingly wide range of 2.4 GHz systems currently available commercially.
Modellers “changing horses” often have to plan for the purchase of complete transmitters as well as new receivers. Only in a very few cases is it possible to transfer model memories; in most cases the model memories have to be re-configured.
Continued availability of many systems over a period of many years may also be uncertain.

This is our solution:
Schulze offers a transmitter module system which can be installed in existing transmitters in just a few minutes.
The aerials can be positioned in the most favourable direction for transmission
(see picture, i.e. the aerial(s) must not be directed straight at the model!).

Safety advantage using 2 transmitter aerials:
The module can be purchased in versions with one or two aerials, the latter offering always a tremendous safety advantage.

The transmitter aerials shall directed (as well as diversity receiver aerials)  90° to each other.
That's why it is not possible to "aim" directly at the model by mistake.

The same applies to our receivers: the larger receiver cases house two receiving sections for best possible diversity reception.

The receivers are protected against wrong voltage polarity.

Our 2.4 GHz system is compatible with other manufacturers’ equipment which uses the same transmission coding. For this reason please look for the slogan or logo “S3D compatible” - this will quickly help you locate the product which matches your model best.

Logo 2,4 GHz kompatibel Logo 2,4 GHz compatible

Transmission process:
Spread Spectrum System with (Dual-) Frequency-Hopping (FHSS)

More highlights:
The µwave receivers and uno/duo-wave transmitter modules can be upgraded from yourself to the latest firmware version!

The servo pulse repetition rate can be varied on the µwave receivers at the binding procedure.
Normally a repetition rate of 18 ms is used which is good for all servos.
Alternatively 14,26 ms can be selected.

The µwave receivers can be configured via "POSE" which is "more than" S3D kompatible.
(Note: The "POSE" interface is not part of the S3D transmit and receive coding.)

The µwave receivers switch off the servo pulses when they received bad signals from the transmitter in the case when no failsafe was configured. This is the best safety feature - because the most electronic speed controllers will shut off the motor when the servo signal is missing!

The uno/duo-wave transmit modules have a transmitting power circuit which works very efficient - this leads to a lower current consumption and less heat.

A back channel with reduced power is existing.
Is the model in reception range of the transmitter (max. about 20 m ... 50 m) then the buzzer in the transmit module is activated to warn the pilot when the receiver battery has under-voltage.


Receivers
Order-
information
Short description         Prices         Hot-Links
µwave-12.WA
 
µwave-12-WA
2,4 GHz receiver with two wire-antennas
 
(Length about 175 mm + 290 mm fixed mounted)

Included
One builtd-in binding button.

Characteristics
2 complete reception units for
a true parallel operating diversity function.
Full range.

12 channels
Horizontal servo connectors
High current connector for the receiver battery
66 * 46 * 23 mm
About 44 g

Recommended accessory (not included)
Additional binding button (for external use).
incl. 19% V.A.T.
159,90 €
Shipping costs
without V.A.T.
(134,37 €)
Specifications

Operating instructions

Firmware update

Accessories
µwave-12.FA
 
µwave-12-FA
2,4 GHz receiver with 2 fixed mounted antenna connectors

Included
2 wire antennas (Ant-RX-W250R and Ant-RX-W400R)
(250 and 400 mm) with screwed joint.
One built-in binding button.

Accessories
Antenna coax cable extension.
Dipole antenna (Ant-RX-S105R, about 105 mm).
Short dipole antenna (Ant-RX-S32R, about 32 mm).

Characteristics
2 complete reception units for
a true parallel operating diversity function.
Full range.

12 channels
Horizontal servo connectors
High current connector for the receiver battery
66 * 46 * 23 mm
About 44 g

Recommended accessory (not included)
Additional binding button (for external use).
incl. 19% V.A.T.
189,90 €
Shipping costs
without V.A.T.
(159,58 €)
Specifications

Operating instructions

Firmware update

Accessories
µwave-12.XA
 
µwave-12-XA
2,4 GHz receiver with 2 antenna-screwed joints on
two fixed mounted antenna coax cable extensions

(Length about 250 mm, e.g. to mount across the fuselage).

Included
Two dipole antennas (Ant-RX-S105R, about 105 mm)
One built-in binding button.

Accessories
Antenna coax cable extension,
wire antennas.

Characteristics
2 complete reception units for
a true parallel operating diversity function.
Full range.

12 channels
Horizontal servo connectors
High current connector for receiver battery.
66 * 46 * 23 mm
About 44 g

Recommended accessory (not included)
Additional binding button (for external use).
incl. 19% V.A.T.
189,90 €
Shipping costs
without V.A.T.
(159,58 €)
Specifications

Operating instructions

Firmware update

Accessories
µwave-8
 
µwave-8
2,4 GHz receiver with 2 wire antennas
(Length about 120 + 180 mm)

Included
One built-in binding button and
and one additional binding jumper.

Characteristics
Two complete reception units for
a true parallel operating diversity function.
Full range.

Surely one of the smallest and most leightweight
true diversity receivers with 8 channels.
Extremely compact
!

Horizontal servo connectors
49 * 21 * 13 mm
About 14 g

Recommended accessory (not included)
Additional binding button (for external use).
incl. 19% V.A.T.
114,90 €
Shipping costs
without V.A.T.
(96,55 €)
Specifications

Operating instructions

Firmware update

Accessories
µwave-8-295
 
µwave-8
2,4 GHz receiver with 2 extremly long wire antennas
(Length of both antennas about 295 mm)

We recommended to use this type of receiver when the mounting position of the receiver with the short antenna wires does not allow sufficient reception.

All other data are identical to the standard µwave-8
incl. 19% V.A.T.
125.90 €
Shipping costs
without V.A.T.
(105.80 €)
Specifications

Operating instructions

Firmware update

Accessories
µwave-4+2.DI
 
µwave-4+2.DI
2,4 GHz Receiver with
dipole antenna
(Length 2 x 30mm)

Included
One built-in binding button and
and one additional binding jumper.

Characteristics
1 reception unit.
Especially for Slow- and Parkflyers.
Range up to 500 m.

4 + 2 channels
(2 channels only equipped with a pulse pin)

Surely one of the smallest and most leightweight
receiver with 6 channels in a case!


Horizontal servo connectors
37 * 20 * 9 mm
About 6.5 g
incl. 19% V.A.T.
59,90 €
Shipping costs
without V.A.T.
(64,90 €)
Specifications

Operating instructions

Accessories
µwave-4+2.WA
 
µwave-2+4
2,4 GHz Receiver with wire antenna
(Length about 120mm)

Included
One built-in binding button and
and one additional binding jumper.

Characteristics
1 reception unit.
Especially for Slow- and Parkflyers.
Range up to 400 m.

4 + 2 channels
(2 channels only equipped with a pulse pin)

Surely one of the smallest and most leightweight
receiver with 6 channels in a case!


Horizontal servo connectors.
37 * 20 * 9 mm
About 6.5 g
incl. 19% V.A.T.
64,90 €
Shipping costs
without V.A.T.
(54,54 €)
Specifications

Operating instructions

Accessories

Transmitting modules

Included
One or two receiving antenna(s)

Build-in and additional binding button/jumper.
It is possible to reduce the transmit power via this button/jumper to make a "range test".

Common features
The back-channel.
Absolutely necessary for the binding procedure.
It has a special function when the receiver battery has under voltage:
The piezo buzzer - build-in in the transmit module - beeps
when the less powerful back channel can be received by the transmitter.
(in the range below 20 m ... 50 m) and the receiver battery has under-voltage.
Order-
information
Short description         Prices         Hot-Links
duo-wave
.GRA-D

 
uno-wave-GRA

Comfortable mounting

Simpliest aerial mounting

Aerial mounting for optimum emission
Plug-in transmitter module for Graupner mc17, mc18, mc20, mc22, mx22(s), mc24
for direct mounting of the transmit aerials.


Contains two fixed mounted screw joints - on which two transmit antennas can directly be mounted
(and then snapped into in different directions of 90° to each other).

Included
Two transmit antennas (Ant-S105R)
One built-in binding button.

Safety hint
This module is made for highest safety because two aerials are sending at the same time with different frequencies.

Mounting hint
The transmit module fits exactly to the existing tray for the old standard transmit module.
The integriated aerial holder is placed directly under the window of the transmitters bottom.

Intelligent
The transmitter is allowed to lay fully plan on the table as before.
At pistol transmitters the aerial holder can be turned 180° that the aerial shows upwards.

Hint
When you own a transmitter without the Graupner standard transmit module, then the duo-wave.UNI is probably the right device and we need your transmitter and/or the exact transmitter type for adapting and mounting.

Recommended accessory (not included)
Additional binding button (for external use).
incl. 19% V.A.T.
169,90 €
Shipping costs
without V.A.T.
(142,77 €)
Specifications

Operating instructions

Accessories
uno-wave
.GRA-D

 
uno-wave-GRA

Comfortable mounting

Simpliest aerial mounting

Aerial mounting for optimum emission

Aerial mounting pistol grip transmitter
Plug-in transmitter module for Graupner mc17, mc18, mc20, mc22, mx22(s), mc24
for direct mounting of the transmit aerials.


Contains one fixed mounted screw joints - on which the transmit antennas can directly be mounted.

Included
One transmit antenna (Ant-TX-S110R)
One built-in binding button.

Mounting hint
The transmit module fits exactly to the existing tray for the old standard transmit module.
The integriated aerial holder is placed directly under the window of the transmitters bottom.

Intelligent
The transmitter is allowed to lay fully plan on the table as before.
At pistol transmitters the aerial holder can be turned 180° that the aerial shows upwards.

Hint
When you own a transmitter without the Graupner standard transmit module, then the uno-wave.UNI is probably the right device and we need your transmitter and/or the exact transmitter type for adapting and mounting.

Recommended accessory (not included)
Additional binding button (for external use).
incl. 19% V.A.T.
129,90 €
Shipping costs
without V.A.T.
(109,16 €)
Specifications

Operating instructions

Accessories
duo-wave
.GRA-K

 
duo-wave-GRA

Comfortable mounting

Aerial mounting

Aerial
mounting II


Aerial
mounting III

Plug-in transmitter module for
e.g. Graupner mc17, mc18, mc20, mc22, mx22(s), mc24
With cables for the transmit aerials.


Equipped with two antenna cables (length about 240 mm each) with a final screw joint - on which the antennas are tighten.

Included
Two transmit antennas (Ant-TX-S110R)
One built-in binding button.

Safety hint
This module is made for highest safety because two aerials are sending at the same time with different frequencies.

Mounting hint
The transmit module fits exactly to the existing tray for the old standard transmit module.
The antenna cables can then be
A) pushed either through the clear-sighted removable cover of the transmitter bottom to be mounted at the "Ant-Halter-DUO", or
B) are fastened inside the transmitter case. The antenna screw joints must be fitted into holes into the transmitter housing (which has to be drilled by yourself at a proper place if necessary).

Hint
When you own a Graupner transmitter without a standard transmitter module shaft, then the duo-wave.UNI is probably the right for you.

Recommended accessory (not included)
Additional binding button (for external use).
incl. 19% V.A.T.
189,90 €
Shipping costs
without V.A.T.
(159,58 €)
Specifications

Operating instructions

Accessories
uno-wave
.GRA-K

 
uno-wave-GRA

Comfortable mounting

Aerial
mounting I


Aerial
mounting II


Aerial
mounting III

Plug-in transmitter module for
e.g. Graupner mc17, mc18, mc20, mc22, mx22(s), mc24
With cables for the transmit aerials.


Equipped with one antenna cable (length about 240 mm) with a final screw joint - on which the antenna is tighten.

Included
One transmit antenna (Ant-TX-S110R)
One built-in binding button.

Mounting hint
The transmit module fits exactly to the existing tray for the old standard transmit module.
The antenna cables can then be
A) pushed either through the clear-sighted removable cover of the transmitter bottom to be mounted at the "Ant-Halter-DUO", or
B) are fastened inside the transmitter case. The antenna screw joints must be fitted into holes into the transmitter housing (which has to be drilled by yourself at a proper place if necessary).

Hint
When you own a Graupner transmitter without a standard transmitter module shaft, then the uno-wave.UNI is probably the right for you.

Recommended accessory (not included)
Additional binding button (for external use).
incl. 19% V.A.T.
149,90 €
Shipping costs
without V.A.T.
(125,97 €)
Specifications

Operating instructions

Accessories
duo-wave
.MPX

 
duo-wave-MPX

Comfortable mounting

Aerial
mounting I


Aerial
mounting II

Plug-in transmitter module for
e.g. Multiplex mc3010, mc3030, mc4000


Equipped with two antenna cables (length about 240 mm each) with a final screw joint - on which the antennas are tighten.

Included
Two transmit antennas (Ant-TX-S110R)
One built-in binding button (for external use).

Safety hint
This module is made for highest safety because two aerials are sending at the same time with different frequencies.

Mounting hint
The transmitter module should be mounted on an open area inside the transmitter housing.
The antenna cables can then be
A) pushed either through the clear-sighted removable cover of the transmitter bottom to be mounted at the "Ant-Halter-DUO", or
B) are fastened inside the transmitter case. The antenna screw joints must be fitted into holes into the transmitter housing (which has to be drilled by yourself at a proper place if necessary).

Hint
When you own a MPX transmitter without a standard transmitter module shaft, then the duo-wave.UNI is probably the right for you.

Recommended accessory (not included)
Additional binding button (for external use).
incl. 19% V.A.T.
169,90 €
Shipping costs
without V.A.T.
(142,77 €)
Specifications

Operating instructions

Accessories
uno-wave
.MPX

 
uno-wave-MPX

Comfortable mounting

Aerial
mounting I


Aerial
mounting II


Aerial
mounting III

Plug-in transmitter module for
e.g. Multiplex mc3010, mc3030, mc4000


Equipped with one antenna cable (length about 240 mm) with a final screw joint - on which the antenna is tighten.

Included
One transmit antenna (Ant-TX-S110R)
One built-in binding button.

Mounting hint
The transmitter module should be mounted on an open area inside the transmitter housing.
The antenna cable can then be
A) pushed either through the clear-sighted removable cover of the transmitter bottom to be mounted at the "Ant-Halter-UNO", or
B) is fastened inside the transmitter case. The antenna screw joint must be fitted to a hole into the transmitter housing (which has to be drilled by yourself at a proper place if necessary).

Hint
When you own a MPX transmitter without a standard transmitter module shaft, then the uno-wave.UNI is probably the right for you.

Recommended accessory (not included)
Additional binding button (for external use).
incl. 19% V.A.T.
129,90 €
Shipping costs
without V.A.T.
(109,16 €)
Specifications

Operating instructions

Accessories
duo-wave
.UNI

 
duo-wave-uni

Comfortable mounting

Aerial mounting
(study)

Universal transmit module
for mounting into many transmitters

(fitting also for the standard shafts of Futaba FF-7 (T7U), FF-8 (T8U), FF-9 (TC9CP), FF-10 (TC10C), PCM 1024-9Z, F-16, FC18, FC28).
For Graupner mc22 via an adapter cable.

Equipped with two antenna cables (length about 240 mm each) with a final screw joint - on which the antennas are tighten.

Included
Two transmit antennas (Ant-TX-S110R)
One built-in binding button.

Safety hint
This module is made for highest safety because two aerials are sending at the same time with different frequencies.

Mounting hint
The transmitter module should be mounted on an open area inside the transmitter housing.
The antenna cables can then be
A) pushed either through the clear-sighted removable cover of the transmitter bottom to be mounted at the "Ant-Halter-DUO", or
B) are fastened inside the transmitter case. The antenna screw joints must be fitted into holes into the transmitter housing (which has to be drilled by yourself at a proper place if necessary).

Hint
This module is also the right if you want to use the transmitter with the old frequency. The 2,4 GHz module then has to be activated by the "S3D-switch-it".

Recommended accessory (not included)
Additional binding button (for external use).
incl. 19% V.A.T.
169,90 €
Shipping costs
without V.A.T.
(142,77 €)
Specifications

Operating instructions

Accessories
uno-wave
.UNI

 
uno-wave-uni

Comfortable mounting

Aerial mounting
(study)

Universal transmit module
for mounting into many transmitters

(fitting also for the standard shafts of Futaba FF-7 (T7U), FF-8 (T8U), FF-9 (TC9CP), FF-10 (TC10C), PCM 1024-9Z, F-16, FC18, FC28).
For Graupner mc22 via an adapter cable.

Equipped with one antenna cable (length about 240 mm) with a final screw joint - on which the antenna is tighten.

Included
One transmit antenna (Ant-TX-S110R)
One built-in binding button.

Mounting hint
The transmitter module should be mounted on an open area inside the transmitter housing.
The antenna cables can then be
A) pushed either through the clear-sighted removable cover of the transmitter bottom to be mounted at the "Ant-Halter-DUO", or
B) are fastened inside the transmitter case. The antenna screw joints must be fitted into holes into the transmitter housing (which has to be drilled by yourself at a proper place if necessary).

Hint
This module is also the right if you want to use the transmitter with the old frequency. The 2,4 GHz module then has to be activated by the "S3D-switch-it".

Recommended accessory (not included)
Additional binding button (for external use).
incl. 19% V.A.T.
129,90 €
Shipping costs
without V.A.T.
(109,16 €)
Specifications

Operating instructions

Accessories

Copyright © 1996-2012 Schulze Elektronik GmbH.
All trademarks shown are trademarks of their respective owners.
All rights reserved.
http://www.schulze-elektronik.com, designed by matthias schulze